Skip to content

Steel Road Barriers & Highway Safety Barriers

Highway safety barriers separate traffic from hazards — oncoming lanes, steep drops, fixed objects and work zones. SinoBarrier manufactures steel and metal beam barrier systems in-house, galvanized to AASHTO M180 and crash-tested to MASH TL3, for roads, medians and temporary work-zone protection.

Barrier types we supply

Barrier type Where it is used
W-beam guardrail Standard highway runs, medians and ramps
Thrie-beam guardrail Bridges, transitions and high-risk curves
Rolling barrier Expressways and alignments needing energy absorption
Steel work-zone barrier Temporary protection in construction and maintenance

Choosing the right system

The correct barrier depends on three things: the road class, the speed, and what is behind the barrier. A wide-shoulder rural road needs a different system from a narrow median on an expressway. Send the road class and posted speed, and we recommend the beam profile, post spacing and test level.

Standards and documentation

All systems are hot-dip galvanized to AASHTO M180 and crash-tested to MASH. Mill test certificates, coating-weight reports and crash-test documentation ship with every order.

Containment level, working width and impact severity

Three numbers describe a barrier system and they are not interchangeable. Containment level says what the system can hold: the mass and the speed of the vehicle it is expected to redirect. Working width says how much room it needs behind the posts to deflect into. Impact severity describes what the occupants experience during the impact rather than what the barrier survives.

A tender that names only the containment level has specified a third of the requirement. Bridge decks, tunnel walls and narrow medians are exactly the locations where the other two decide the answer, because a system can hold the required vehicle and still be unusable where there is no space to deflect into — or unacceptable because it transfers too much force to the occupants at the angle the site produces.

The system families, compared

System How it holds a vehicle Space it needs Where it suits
W-beam on C or U posts A double-wave steel rail deflects under load and redirects the vehicle along its face Moderate — the post line plus its working width behind Open runs, embankments and verges at ordinary containment levels
Thrie-beam on posts A deeper, stiffer section resists bending further before it yields Less than a W-beam at the same level Bridges, tunnel portals, high-speed corridors, anywhere the offset is fixed
Rolling barrier Rotating cylinders convert part of the forward motion into rotation rather than into deformation Very little — the smallest of the three Curves, narrow structures, median openings and shallow impact angles
Mixed run with transitions Each section does the job it suits best, and a transition carries the change of profile Set by the stiffest section in the run The ordinary real answer: W-beam on the approach, thrie-beam through the structure

Where barrier runs sit on a road project

  • Mainline verge. The straightforward case: a run at the standard offset on driven posts, with a terminal at each end chosen by approach direction.
  • Median. A double-sided barrier, where the offset is set from both carriageways rather than one and the run usually has to be maintained from a single side.
  • Bridge deck. The offset is fixed by the deck width and the anchorage changes from driven posts to a baseplate and a cast-in arrangement. Here the deflection limit, not the containment level, decides the profile.
  • Gore and ramp areas. The impact angle is shallower than on the mainline and the run is short, so the end treatments carry a disproportionate share of the risk.
  • Temporary and work-zone barriers. Often the same hardware at a tighter post spacing, moved as the works progress, which makes the release detail and the fixing pack worth specifying rather than leaving to the contractor.

Specification questions on barrier systems

What containment level does our road need?
It follows from the vehicle mix, the operating speed and the consequence of a vehicle leaving the carriageway. Most national standards give a table mapping road class to level; where a project has no such table, send the site condition and we will recommend a level and the system that reaches it.
How much room does a barrier need behind it?
It depends on the system and the level. A W-beam needs noticeably more working width than a thrie-beam, and a rolling barrier needs the least of the three. If there is a structure immediately behind the post line, that figure decides the specification before anything else does.
Are the posts and the beam supplied together?
Yes, and the fixing pack with them, so the bolts, washers and spacers arrive matched to the sections rather than to a nominal size. A consignment that is correct on paper and does not assemble on site is almost always a fixing pack bought separately.
Can you match a barrier to an existing bridge parapet?
Usually, by working from the parapet detail rather than from a standard drawing. Send the parapet section and the deck width and we will come back with the profile and the anchorage that fits the space available, instead of a standard run that has to be altered on site.

Request highway barrier pricing

Next step

Send us your requirement

For a quotation, include the product type, quantity, required standard and destination port. Email your drawing or bill of quantities if available.

We reply within one working day. Your details stay with our sales team only.

Need a quotation for your next highway project?

Send the drawing, the bill of quantities or just the standard you are building to. We return a take-off, a shop drawing and a factory price within one working day.

Chat on WhatsApp