Skip to content

MASH TL4 & EN 1317 Crash Testing

MASH (the Manual for Assessing Safety Hardware) is the full-scale crash-test standard that verifies a barrier actually redirects a vehicle. EN 1317 is the European equivalent. SinoBarrier roller barrier systems are crash-tested to MASH TL4 across the full test matrix, and supplied with EN 1317 documentation for projects delivered into the EU.

What MASH test levels mean

A test level (TL) defines the vehicle and impact condition a barrier must survive. Higher levels mean heavier vehicles and faster, more severe impacts.

Test level Vehicle Typical application
MASH TL3 2270 kg pickup truck at 100 km/h Standard highways and arterial roads
MASH TL4 10,000 kg single-unit truck at 90 km/h Expressways, high-speed and high-risk sites

Our roller barrier: TL4, full test matrix

Our roller barrier is crash-tested to MASH TL4. It passed all three impact conditions that make up the TL4 matrix for a longitudinal barrier, so the result is a full TL4 pass rather than a partial one.

MASH test Vehicle Impact speed Impact angle
Test 4-10 1100 kg passenger car 100 km/h 25°
Test 4-11 2270 kg pickup truck 100 km/h 25°
Test 4-12 10,000 kg single-unit truck 90 km/h 15°

Test 4-12 is the condition that separates TL4 from TL3: a 10,000 kg single-unit truck at 90 km/h and a 15° angle. Ask for the test report with your quotation.

What EN 1317 adds for European projects

EN 1317 classifies a barrier by its containment level, working width and impact severity — three values that together tell you how the barrier behaves and how much space it needs. SinoBarrier supplies CE documentation alongside the test report for projects that must show EN 1317 conformance.

Which level does your project need?

  • TL3 — adequate for most highway and urban road applications.
  • TL4 — required for expressways, tunnels, bridge approaches and any site where trucks are part of the traffic mix.

Send the road class, the posted speed and the traffic mix, and we confirm the test level and the roller barrier configuration that meets it.

Documentation we supply

  • Full-scale crash test report for the tested configuration
  • MASH test level and EN 1317 containment class
  • CE documentation for EU projects
  • Working width and deflection data for layout planning

How a MASH test is actually run

A MASH certification is not a single pass-or-fail event. The manual defines a matrix of tests by vehicle class, impact speed and impact angle, and a system is certified at a level only when it has been evaluated across the tests that level requires. The test article is the real assembly — the actual rail, the actual posts at the actual spacing, on a foundation built to the installation drawing — because a result only transfers to the configuration that was on the track.

Behavior is judged on more than whether the vehicle stayed on the road. The evaluation also looks at whether the vehicle was redirected or was snagged and spun, whether it rolled, whether the occupant compartment was breached, and how far the barrier deflected behind its original line. That last figure is the one that most often decides a design: a system can pass and still be unusable on a bridge deck where there is no room behind the barrier to deflect into.

What to ask for in the documentation

Ask for the test matrix rather than for a certificate of compliance, then check the supplied configuration against the tested one. The three things worth confirming are the rail height and roller diameter, the post section and spacing, and the foundation arrangement. Where any of those differ from the tested article, the result does not carry over, and the report should say so rather than leave it to be inferred.

Our roller barrier is certified to MASH TL4 across the full test matrix on the H250 rail with φ350 mm rollers — the configuration that ships. For European projects the same systems are supplied with EN 1317 documentation, whose containment classes and working-width classes are a different vocabulary for a similar set of questions.

Frequently asked questions

What is the difference between a certificate and a test matrix?
A certificate says a system was evaluated and passed. The matrix says which vehicle classes, speeds and angles were run, which is the part that lets you check that the configuration being supplied is the configuration that was tested. Always ask for the matrix.
Does the tested configuration have to match what we install?
Yes. A crash test result transfers only to the article that was on the track — the same rail, the same post section and spacing, the same foundation. Changing any of them means the result no longer describes what is being installed.
Our project is specified to EN 1317, not MASH. Is that a problem?
No. EN 1317 asks a similar set of questions in a different vocabulary, using containment classes and working-width classes rather than test levels. European projects are supplied with EN 1317 documentation for the same systems.
Where is the roller barrier MASH TL4 record published?
On the roller barrier MASH TL4 page, including the test matrix and the configuration it applies to. It is written so a project engineer can check the certificate against the article being quoted.

Request test documentation

Next step

Send us your requirement

For a quotation, include the product type, quantity, required standard and destination port. Email your drawing or bill of quantities if available.

We reply within one working day. Your details stay with our sales team only.

Need a quotation for your next highway project?

Send the drawing, the bill of quantities or just the standard you are building to. We return a take-off, a shop drawing and a factory price within one working day.

Chat on WhatsApp