Skip to content

Crash Barrier for the UAE, Saudi Arabia and the Gulf

Crash barrier and road barrier for UAE and Saudi highways, built to RTA, DMT and Ministry of Transport drawings, shipped to Jebel Ali and Dammam.

SinoBarrier manufactures crash barrier and road barrier — w beam, thrie beam and roller barrier — for expressways, bridges, industrial cities and logistics parks in the UAE, Saudi Arabia and the wider Gulf, in our own factory in Shandong, China, operating since 2010. We roll, punch and hot-dip galvanize in-house and ship the complete system — beam, post, blocking piece, terminal and bolts — in one container. 28+ countries and 555+ projects supplied.

We build to the contract drawing and specification. Send the drawing, the bill of quantities, or the clause your engineer is working to — a Dubai RTA or Abu Dhabi municipal specification, a Saudi Ministry of Transport drawing, an industrial-client specification, or a consultant’s design written to EN 1317 — and we confirm containment level, section, post and coating before quoting.

The projects we have already supplied in the region — desert expressways, bridge works and industrial compounds — are described on road safety barriers for the Middle East.

Crash barrier types, and which one a Gulf project specifies

Most of the search traffic on this subject is people trying to work out which system they need, so here is the comparison we use on site. In Arabic tender documents the item usually appears as حاجز طريق or حاجز حماية; on site it is often called Armco barrier, whichever system the drawing actually shows.

Type How it behaves in an impact Where Gulf projects specify it
Concrete (Jersey / New Jersey profile) Rigid. Very little deflection, so it holds a tight working width but transfers most of the load to the deck or subgrade Bridge decks, tunnel portals, toll plazas and medians with no room to deflect. Usually cast by a local precast yard; what we supply is the steel-to-concrete transition and the approach terminal
Steel w beam Flexible. The beam yields and the posts pull, redirecting the vehicle over a longer distance Shoulders, embankments, intercity and rural roads — the default system on the majority of the network
Steel thrie beam Stiffer and taller than w beam, three waves instead of two, so it resists heavier vehicles and higher impact angles Bridges, flyovers, transitions where the barrier meets a parapet, and freight corridors
Roller barrier Rotating cylinders turn the vehicle back along the barrier instead of absorbing the hit in the rail Sharp curves, steep descents, tunnel approaches and urban blackspots where the run is short and the hit is frequent
Cable barrier Cable and weak posts, very long deflection, cheapest per metre of median Wide medians with a large clear zone. Not part of our range — we say so rather than quote around it

Road barrier systems we supply

Product Typical use in the Gulf
W-BEAM guardrail Shoulders and medians of intercity roads, industrial city access roads, logistics yards
THRIE BEAM guardrail Bridges, flyovers, transitions and heavy-vehicle routes
Posts and blocking pieces Channel, C and H sections, driven or base-plated per drawing
End terminals and anchorages Run ends, bridge approaches, interchanges and gore areas
Roller barrier Mountain roads, sharp bends, descents and urban blackspots

Tender documents in the region rarely use the same words for the same part. A Dubai consultant may write crash barrier, a Saudi contractor may write guardrail, a subcontractor may write Armco, and the bill of quantities may list beam, post and spacer separately. Send the schedule as it is written and we map our part numbers onto it line by line, so nothing is priced as an assumption.

Specifications

Item Standard
Section Two-wave w beam, 310 mm wide, 83 mm deep; three-wave thrie beam on request
Thickness Beam 2.7 mm, 3.0 mm or 4.0 mm; post and blocking piece 4.5 mm or 6.0 mm
Panel length 4320 mm, 4130 mm or 3810 mm; special lengths to drawing
Post spacing 2 m or 4 m as drawn; closer spacing on bridge approaches
Steel Q235B or S355JR, mill certificate per batch
Coating Hot-dip galvanized, minimum 550 g/m² (AASHTO M180); heavier classes quoted for coastal sites
Impact performance MASH TL3 assemblies for w beam and thrie beam; roller barrier tested to MASH TL4. EN 1317 containment classes quoted to the class named in the design
Mounting height 706 mm to top of rail on a conventional layout, or per drawing

Coating, heat and sand

Three things in this region shorten a barrier’s life, and only one of them is obvious. Salt air on the coast is the one everybody plans for. The other two are heat and sand: a rail run is roughly 30 m of steel, and over a 60 °C swing between a winter night and a summer afternoon it grows about 20 mm, so a run installed tight in January will buckle or tear its anchorages in July unless the drawing’s expansion detail is followed. Wind-borne sand blasts the coating on the windward face and piles up at the foot of the posts, which is where the ground-line corrosion starts. Hot-dip galvanizing to 550 g/m² holds on inland sites; for coastal and splash-zone work we quote AASHTO M180 Type II (about 1100 g/m²) or the ISO 1461 thickness your specification names, and where a municipality requires a colour finish, a duplex system — galvanized then powder coated — rather than powder over bare steel.

Country requirements: UAE and Saudi Arabia

Market Specification usually cited What we confirm against it
Dubai Roads and Transport Authority standard drawings and specifications for road works Section, post spacing, coating class, terminal type, and any aesthetic colour requirement
Abu Dhabi and the northern emirates Department of Municipalities and Transport specification, or the federal ministry’s standard drawing for intercity roads Containment level, working width, transition to bridge parapet
Saudi Arabia — intercity Ministry of Transport standard drawing and general specification, administered with the Roads General Authority Beam and post section, splice detail, coating mass, pre-shipment inspection
Saudi Arabia — urban Municipality or Amanah specification, or the consultant’s design Section, colour and hardware to the drawing
Industrial clients, ports and logistics parks The client’s own specification, frequently written around EN 1317 or AASHTO Containment class, coating, and the inspection regime the client’s engineer runs

Each authority words the clause differently, and the difference usually lands on coating class, post spacing or terminal type. Tell us which clause applies and we confirm in writing, before quoting, the section, post and coating that meet it.

Shipping to Gulf ports

  • UAE: Jebel Ali, Khalifa Port, Port Rashid, Khor Fakkan and Fujairah.
  • Saudi Arabia: King Abdulaziz Port Dammam, Jeddah Islamic Port, King Abdullah Port, Jubail and Ras Al Khair.
  • Elsewhere in the Gulf: Hamad (Qatar), Sohar (Oman), Shuwaikh (Kuwait), Khalifa bin Salman (Bahrain) and Umm Qasr (Iraq).
  • Lead time: 15–25 days after drawing approval and deposit, plus sea transit; a Gulf port is typically 18–30 days from Shanghai or Qingdao.
  • Documents: commercial invoice, packing list, bill of lading, certificate of origin, mill certificates, coating-weight report and third-party inspection report (SGS, BV or Intertek) where the contract requires pre-shipment inspection.
  • Saudi clearance: the importer’s agent raises the SABER shipment certificate; we supply the test reports, product data and mill certificates that certificate is issued against, so the file is complete before the vessel sails.
  • Loading: nested beams and mixed containers, so the site does not wait for a second container of bolts.

How to get a quotation

  1. Send the drawing, the bill of quantities, or just the run length and barrier type.
  2. We return a material take-off, fabrication drawing and price within one working day.
  3. Minimum order: one 20GP container (about 25 tonnes, or a mixed container). Payment: 30% deposit by T/T and balance against B/L, or L/C at sight.

Frequently asked questions

What is the difference between a crash barrier, a road barrier and a guardrail?
They are largely the same family of product, named by function rather than by shape. Crash barrier and road barrier describe what the system does — contain and redirect a vehicle — while guardrail and Armco describe the steel beam system itself. What decides the price and the performance is not the name but the assembly: beam section and thickness, post type and spacing, terminals, and coating class.
Which crash barrier do UAE and Saudi projects normally use?
Steel w beam on shoulders and medians, thrie beam where the run meets a bridge parapet or carries heavy trucks, concrete where the working width is tight, and roller barrier on curves and descents. The drawing names the containment class; we quote the system that meets it rather than the other way round.
Can you supply to EN 1317 or MASH?
Yes. Where the design is written to EN 1317 we quote to the containment class and working width it names; our w beam and thrie beam assemblies are supplied to MASH TL3 and the roller barrier is tested to MASH TL4. Send the clause and we confirm which of our assemblies satisfies it.
What does a crash barrier cost per metre?
It depends on beam thickness, coating class, post and blocking piece weight, terminal type and run length. A complete run shipped with posts and terminals in the same container usually costs less per metre than buying beams alone and sourcing hardware locally. Send the run length and type and we quote within one working day.
What documents does a Saudi shipment need?
Commercial invoice, packing list, bill of lading, certificate of origin, mill certificates and a coating-weight report, plus the SABER shipment certificate raised by the importer’s agent. Our test reports and product data are issued in the form that certificate is built on, and we can add pre-shipment inspection by SGS, BV or Intertek if the contract calls for it.
How long is delivery to Jebel Ali or Dammam?
Production is 15–25 days after drawing approval and deposit. Sea transit from Qingdao or Shanghai is typically 18–30 days to a Gulf port, depending on the route, the carrier and whether the vessel is direct or tranships.

Request a quotation

Tell us the run length, barrier type and destination port. If you have the drawing or bill of quantities, send it too. Request a quote or message us on WhatsApp.

Next step

Send us your requirement

For a quotation, include the product type, quantity, required standard and destination port. Email your drawing or bill of quantities if available.

We reply within one working day. Your details stay with our sales team only.

Need a quotation for your next highway project?

Send the drawing, the bill of quantities or just the standard you are building to. We return a take-off, a shop drawing and a factory price within one working day.

Chat on WhatsApp