Skip to content

W-Beam Guardrail Specifications

Short answer: a standard W-beam guardrail panel is a 310 mm wide, 83 mm deep corrugated steel section, rolled in 3.0 mm steel as standard or 4.0 mm to order, in 4320 mm, 4130 mm or 3810 mm lengths, from Q235B or S355JR, hot-dip galvanized to a minimum 550 g/m² coating weight under AASHTO M180. A 4320 mm panel in 3.0 mm steel weighs approximately 49 kg. Every value below is verifiable against the mill certificate and coating test report that ship with each batch.

·, Technical Lead

W-beam guardrail panels stacked at the SinoBarrier factory before galvanizing

W-beam — Panel length: 2320 / 3320 / 4128 / 4130 / 4318 / 4320 / 7938 mm; Section width: 308 / 310 / 311 / 312 / 315 mm; Base metal thickness: 2.5 / 2.6 / 2.67 / 2.7 / 2.75 / 2.76 / 2.8 / 3 / 4 / 5 / 10 mm; Nominal base thickness: Class A: 2.67 mm; Class B: 3.43 mm. Custom dimensions and acceptance requirements are confirmed against the approved drawing and order specification.

This page collects the W-beam guardrail specifications a procurement or engineering team needs in one place, with the standard reference behind each value — so the numbers can go straight into a tender or a comparison against another supplier’s data sheet.

Section dimensions

Parameter Value
Profile W-beam
Panel length 2320 / 3320 / 4128 / 4130 / 4318 / 4320 / 7938 mm
Section width 308 / 310 / 311 / 312 / 315 mm
Base metal thickness 2.5 / 2.6 / 2.67 / 2.7 / 2.75 / 2.76 / 2.8 / 3 / 4 / 5 / 10 mm
Nominal base thickness Class A: 2.67 mm; Class B: 3.43 mm
Steel grade A572 / Q345B / HA350 / Q235B / A36 / S355JR / S275JR
Zinc coating mass Type I: 550 g/m²; Type II: 1100 g/m²; 300 / 550 / 610 / 900 / 1100 / 1220 g/m²
Approximate coating thickness 300 g/m² ≈ 40 µm; 550 g/m² ≈ 80 µm; 610 g/m² ≈ 85 µm; 1100 g/m² ≈ 160 µm; 1220 g/m² ≈ 170 µm
Surface treatment Hot-dip galvanized / powder coated
Standard AASHTO M180

Custom dimensions and acceptance requirements are confirmed against the approved drawing and order specification. Confirm the standard edition, coating type, measurement area and test method on the order. The micrometre figures are approximate catalogue pairings, not a sum across two faces or an acceptance test.

Close-up of hot-dip galvanized W-beam guardrail section, 550 g/m² coating
The galvanized surface is the barrier’s armour — coating weight, not appearance, is the specification number.

Material and coating

Steel grade A572 / Q345B / HA350 / Q235B / A36 / S355JR / S275JR
Zinc coating mass Type I: 550 g/m²; Type II: 1100 g/m²; 300 / 550 / 610 / 900 / 1100 / 1220 g/m²

How the coating classes differ between the American and European systems — and what to write into a specification — is compared on our galvanized guardrail standards page.

Weight per metre and per kilometre

At approximately 49 kg per 4320 mm panel, a 3.0 mm W-beam section weighs in the region of 11.4 kg per metre of steel, or about 12.3 kg per metre of installed barrier once the 320 mm splice lap is taken up — before posts, blocks and fixings. For freight planning: a full 20GP container carries roughly 25 tonnes, which is on the order of 500 panels or about 2 km of single-sided rail. Project BOQs usually add 12–15% for posts, blocks and terminals to the rail tonnage.

Posts, blocks and fixings that complete the system

The panel is one third of the system. A complete run needs:

  • Posts — I-beam, C-channel, sigma, round or U sections; drilled and punched to match the panel. The options are on the guardrail posts page.
  • Offset blocks and spacers — box, C, U, H, F and trapezoidal profiles that hold the beam off the post and add deflection travel.
  • Fixings — M20 bolts, nuts and washers galvanized to match the panels.
  • End treatments — flared, buffer, fishtail and bullnose terminals; the selection logic is on our end terminal types page.
W-beam guardrail installed along a highway, galvanized finish
The same section, installed: 310 mm × 83 mm corrugation at 550 g/m² galvanizing.

How these values are verified

Every production batch ships with three documents: the mill certificate for the base metal, the coating-weight test report for the galvanizing, and a certificate of conformity to AASHTO M180. For a tender, all three are available up front with the quotation — ask for them before you compare prices, because a W-beam that cannot produce its coating report is not the same product regardless of its price.

See the W-beam guardrail page

FAQ

What thickness is standard W-beam guardrail?

The standard thickness is 3.0 mm; 4.0 mm is produced for heavier containment duty and 12 ga (2.67 mm) where an AASHTO drawing calls for it. All three come off the same 310 mm × 83 mm corrugation and all carry the AASHTO M180 coating requirement, so the gauge changes the mass and the strength, not the profile.

What is the galvanizing coating weight on W-beam guardrail?

Zinc coating mass: 300 / 550 / 610 / 900 / 1100 / 1220 g/m². Type I: 550 g/m²; Type II: 1100 g/m². Approximate coating thickness: 300 g/m² ≈ 40 µm; 550 g/m² ≈ 80 µm; 610 g/m² ≈ 85 µm; 1100 g/m² ≈ 160 µm; 1220 g/m² ≈ 170 µm. Confirm the standard edition, coating type, measurement area and test method on the order. The micrometre figures are approximate catalogue pairings, not a sum across two faces or an acceptance test.

What lengths does W-beam guardrail come in?

W-beam — Panel length: 2320 / 3320 / 4128 / 4130 / 4318 / 4320 / 7938 mm; Section width: 308 / 310 / 311 / 312 / 315 mm; Base metal thickness: 2.5 / 2.6 / 2.67 / 2.7 / 2.75 / 2.76 / 2.8 / 3 / 4 / 5 / 10 mm; Nominal base thickness: Class A: 2.67 mm; Class B: 3.43 mm. Custom dimensions and acceptance requirements are confirmed against the approved drawing and order specification.

How much does a W-beam panel weigh?

Approximately 49 kg for a 4320 mm panel in 3.0 mm steel, which is about 11.4 kg per metre of steel and about 12.3 kg per metre of installed barrier once the splice lap is taken up. A 4.0 mm panel is about 65 kg, and about 25 tonnes of mixed rail, posts and fixings fill a 20GP container.

Need this specified for a live project?

Request a quotation

Need a quotation for your next highway project?

Send the drawing, the bill of quantities or just the standard you are building to. We return a take-off, a shop drawing and a factory price within one working day.

Chat on WhatsApp