Skip to content

W-Beam Guardrail Manufacturer & Supplier

SinoBarrier supplies W-beam panels with matching posts, spacers, terminals and fasteners. Use this page to check the system layout and supply scope. For individual panel options, compare W-beam finishes.

W-beam guardrail specifications and dimensions

Parameter Value
Profile W-beam
Panel length 2320 / 3320 / 4128 / 4130 / 4318 / 4320 / 7938 mm
Section width 308 / 310 / 311 / 312 / 315 mm
Base metal thickness 2.5 / 2.6 / 2.67 / 2.7 / 2.75 / 2.76 / 2.8 / 3 / 4 / 5 / 10 mm
Nominal base thickness Class A: 2.67 mm; Class B: 3.43 mm
Steel grade A572 / Q345B / HA350 / Q235B / A36 / S355JR / S275JR
Zinc coating mass Type I: 550 g/m²; Type II: 1100 g/m²; 300 / 550 / 610 / 900 / 1100 / 1220 g/m²
Approximate coating thickness 300 g/m² ≈ 40 µm; 550 g/m² ≈ 80 µm; 610 g/m² ≈ 85 µm; 1100 g/m² ≈ 160 µm; 1220 g/m² ≈ 170 µm
Surface treatment Hot-dip galvanized / powder coated
Standard AASHTO M180

Custom dimensions and acceptance requirements are confirmed against the approved drawing and order specification. Confirm the standard edition, coating type, measurement area and test method on the order. The micrometre figures are approximate catalogue pairings, not a sum across two faces or an acceptance test.

Confirm the complete system

  • Panel: profile, thickness, overall length, effective installed length and hole pattern.
  • Posts and spacers: section, spacing, mounting height, embedment or base-plate detail.
  • Connections: splice position, fasteners, transitions and terminal model.
  • Documentation: approved drawing, material requirements and applicable test report.

Match these details as a set. A panel name or steel thickness alone does not establish the performance of an installed barrier.

Post spacing, nesting and regional layouts

MGS and JT/T layouts use different panel and post arrangements. Confirm the drawing reference and dimensions before comparing quotations or ordering replacements. See the post-spacing guide.

Distinguish a nested assembly from an ordinary splice and from a double-rail arrangement. Use the specified panel layers, rail height, post schedule and connections; do not substitute a similar-looking layout.

Panel weight and installed length

Section Base-metal gauge Base-metal thickness Panel length Mass per panel
MGS standard 12 ga 2.67 mm 3810 mm ≈ 38.5 kg
JT/T 281 standard 3.0 mm 3.0 mm 4320 mm ≈ 49.2 kg
JT/T 281 heavy 4.0 mm 4.0 mm 4320 mm ≈ 65.6 kg

These catalogue masses are approximate references for the listed panels. Confirm the drawing, coating and complete component schedule for shipping weight. Overall panel length differs from effective installed length after overlaps.

Choose the surface finish

Review AASHTO M180 material information separately from system performance requirements. Match the proposed configuration to the applicable report.

Installation and inspection

Follow the approved installation drawing and the selected system’s instructions. Confirm post spacing, rail height, splice locations, connections and end treatments before work starts. Inspect delivered components and report damage before installation.

W-beam guardrail price: quotation inputs

Send the drawing, quantity, required standard and destination port. Specify panels only or a complete run. Compare prices using the same installed length, component schedule, coating and freight scope.

Frequently asked questions

What is a W-beam guardrail?
A roadside barrier assembly using corrugated steel panels with a W-shaped profile, supported by posts and connected to the specified spacers, terminals and fasteners.
Which dimensions and coatings can I order?
See the main specification table, then confirm the exact combination against the approved drawing. The full catalogue range is not a single tested configuration.
How do I match panels to an existing barrier?
Provide the drawing reference and photographs. Confirm panel dimensions, holes, post spacing, mounting height, connections and terminal details together.
Does a material standard establish crash performance?
Confirm material and coating requirements separately from the applicable system test report. Changes to the tested assembly require review.
What do I need for a quotation?
Send the drawing or bill of quantities, required standard, quantities, delivery port and the components included in the order.

Request W-beam pricing

Next step

Send us your requirement

For a quotation, include the product type, quantity, required standard and destination port. Email your drawing or bill of quantities if available.

We reply within one working day. Your details stay with our sales team only.

Need a quotation for your next highway project?

Send the drawing, the bill of quantities or just the standard you are building to. We return a take-off, a shop drawing and a factory price within one working day.

Chat on WhatsApp