Skip to content
Guardrail End

Bullnose End Terminal

Part of the Guardrail End range · Highway Guardrail.

Model: Bullnose end terminal

A bullnose end terminal rounds off the start of a guardrail run so it can be struck head-on from either direction without spearing the vehicle. The roadway guardrail terminal end are installed at the end of each part of crash barrier system with the aim to prevent damage and harm to pedestrians and vehicles when vehicles become errant and crash at the end of guardrails. Generally speaking, every 1000…

  • Standard AASHTO M180, EN ISO 1461 Chinese National Standard
  • Material Q235B / Q345B steel
  • Surface 550g/m2 (80µ)Surface
  • Thickness 2.75mm,2.85mm,3.75mm,3.85mm,4mm
  • MOQ 1 × 20GP container
  • Lead time 15–25 days
  • Mill test certificate with every shipment
  • Shop drawings and setting-out plan included
  • Custom lengths, hole patterns and coating weights

Technical specification

ItemTerminal End/Bullnose End
SizeR160(320)
Wave Width310, 506,460mm
Wave Height83,85,310mm
Thickness2.75mm,2.85mm,3.75mm,3.85mm,4mm
Zinc coating550g/m2 (80µ)Surface
Surface treatmentHot dip galvanized or powder coated.
StandardAASHTO M180, EN ISO 1461 Chinese National Standard
PurposeFor the end of the section of the road, and for the protection and aesthetic effect of the end of the fence panels guardrail fish tail end
Can tailor-make according to customer’s requirements

Dimensions shown are the standard range. Non-standard lengths, hole patterns and coating weights are produced to order — send your drawing for a confirmation drawing.

Description

Bullnose end terminal: where it is used

The bullnose end is the rounded terminal used where a barrier run ends and has to present a safe, non-spearing face to traffic approaching from either side. The curved end wraps the rail around so a glancing impact is redirected rather than caught, which makes it a good fit for median ends, gore areas and the start of a central reservation barrier. It is normally used where the design speed at the terminal is low.

Galvanized bullnose end terminal

What a bullnose terminal does

A guardrail terminal end, or end treatment, is the engineered piece fitted to the start and end of a barrier run. The bullnose type turns the rail back on itself in a smooth curve, so an errant vehicle meets a rounded surface instead of the cut end of the beam. That removes the risk of the rail spearing the vehicle and stops the end of the run being the most dangerous part of the barrier.

Fixing and installation

Bullnose terminals are bolted to the last posts of the run and to the end of the beam, and their geometry is set by the beam profile and the post spacing in use. Because the end is the first thing a vehicle reaches, the fixing detail matters as much as the section. Tell us the beam profile and the run layout and we supply the terminal and the transition pieces to match.

Standards, sizes and ordering

Bullnose end terminals are produced to AASHTO M180 and hot-dip galvanized, or finished to your own specification with painting or PVC coating on request. Send the beam profile, the terminal type and the quantity and we quote from our own works. For a full run we can supply the terminals with the beams, posts and bolts as one order.

Where a bullnose terminal is used

  • Highway and other high-grade roads, where a run ends in a median opening or a gore area.
  • Bridges and embankments, where the end of the barrier sits above a drop.
  • Any location where traffic can approach the end from either direction, which a one-sided terminal cannot cover.

Specification

  • R160 (320 mm) nose, with wave widths of 310, 460 and 506 mm and wave depths of 83 and 85 mm.
  • Steel 2.75 / 2.85 / 3.75 / 3.85 / 4.0 mm, hot-dip galvanized to 550 g/m² (about 80 µm).
  • All components hot-dip galvanized; fixing matched to the post type.
  • Complies with AASHTO M180 for highway use.

Bullnose guardrail

A bullnose guardrail is the rounded, redirective terminal used where a run ends and traffic can approach from either side — a median opening, a gore area, or the blunt end of a divided highway. Because the curved nose faces both directions, it redirects an impact from either approach, which a one-sided flared or buffer treatment cannot do.

Frequently asked questions

Where is a bullnose terminal used?
Where a barrier run ends and has to present a safe, non-spearing face to traffic approaching from either side: median ends, gore areas and the start of a central reservation. The curved end wraps the rail around so a glancing impact is redirected rather than caught.
What bullnose sizes do you supply?
The bullnose is supplied at R160 (320) mm, with wave widths of 310, 506 and 460 mm and wave heights of 83, 85 and 310 mm, in 2.75, 2.85, 3.75, 3.85 or 4 mm steel. The section is matched to the beam it closes.
What coating does the bullnose carry?
550 g/m² (about 80 µm) hot-dip galvanized, or powder coated, to AASHTO M180 and EN ISO 1461, so the coating of the terminal matches the rest of the run.
Can the end be tailored to the project?
Yes. Bullnose ends are made to order for the section of road and the barrier they close, and non-standard radii, wave widths and lengths are produced to your drawing rather than taken from a fixed list.

Key features

  • Bridge, buffer, fishtail, flared and bullnose end treatments
  • Turns the end of a barrier run into a crashworthy termination
  • Hot-dip galvanized to AASHTO M180 with the rest of the system
  • Shop-welded and jig-checked so it bolts straight to the last post
  • Delivered with the bolt set and an installation sketch

Where it is used

  • Barrier run terminations
  • Bridge and culvert ends
  • Median openings
  • Road junctions and lay-bys
  • Highway maintenance ends
  • Depressed medians

Complete the system

A barrier is supplied as a set. These are the components that go with this item on a typical installation.

Not sure which specification fits?

Tell us the road class, design speed and the standard your client is working to. Our engineer will come back with the section, the coating weight and the post spacing that meet it — and the price for the quantity you need.

Ask an engineer
Related

Other items in this range

Bridge End Terminal
Guardrail End

Bridge End Terminal

Model: Bridge end terminal

Compared to fish tail shape ends, it features holes in the end for convenient bolting the terminal firmly…

View details
Buffer End Terminal
Guardrail End

Buffer End Terminal

Model: Buffer end terminal

Double Terminal End, also known as Buffer End, are mounted on road bends or median strips. the roadway…

View details
Fishtail End Terminal
Guardrail End

Fishtail End Terminal

Model: Fishtail end terminal

The fishtail end terminal is a flared, energy-absorbing end treatment that turns the start of a W-beam run…

View details
Related

More on Guardrail End

Need a quotation for your next highway project?

Send the drawing, the bill of quantities or just the standard you are building to. We return a take-off, a shop drawing and a factory price within one working day.

Chat on WhatsApp