Skip to content
Thrie-Beam Guardrail

AASHTO M180 Thrie-Beam Highway Guardrail

Part of the Thrie-Beam Guardrail range · Highway Guardrail.

Model: Thrie-Beam / 506 / 508 / 510 mm

Thrie-beam — Panel length: 4120 × 506 × 85 mm / 7920 × 506 × 85 mm; Section width: 506 / 508 / 510 mm; Base metal thickness: 2.76 / 2.8 / 3 / 4 / 4.5 / 5 / 10 mm; Nominal base thickness: Class A: 2.67 mm; Class B: 3.43 mm. Custom dimensions and acceptance requirements are confirmed against the approved drawing and order specification. Type I: 550 g/m²; Type II: 1100 g/m²

  • Standard AASHTO M180 / EN 1317 / AS/NZS 3845-1999
  • Material A572 / Q345B / HA350 / Q235B / A36 / S355JR / S275JR
  • Surface Hot-dip galvanized / powder coated
  • Thickness Class A: 2.67 mm; Class B: 3.43 mm
  • MOQ 1 × 20GP container
  • Lead time 15–25 days
  • Mill test certificate with every shipment
  • Shop drawings and setting-out plan included
  • Custom lengths, hole patterns and coating weights

Technical specification

ParameterValue
ProfileThrie-beam
Panel length4120 × 506 × 85 mm / 7920 × 506 × 85 mm
Section width506 / 508 / 510 mm
Panel length — Notes2320 / 3320 / 4128 / 4218 / 4318 / 4320 mm
Base metal thickness2.76 / 2.8 / 3 / 4 / 4.5 / 5 / 10 mm
Nominal base thicknessClass A: 2.67 mm; Class B: 3.43 mm
Steel gradeA572 / Q345B / HA350 / Q235B / A36 / S355JR / S275JR
Zinc coating massType I: 550 g/m²; Type II: 1100 g/m²; 300 / 550 / 610 / 900 / 1100 / 1220 g/m²
Approximate coating thickness300 g/m² ≈ 40 µm; 550 g/m² ≈ 80 µm; 610 g/m² ≈ 85 µm; 1100 g/m² ≈ 160 µm; 1220 g/m² ≈ 170 µm
Surface treatmentHot-dip galvanized / powder coated
StandardAASHTO M180
Mechanical propertiesRe ≥ 355 MPa; Rm ≥ 495 MPa; A50 ≥ 15%. For the specified high-strength steel grade; verify the grade and batch mill certificate.

Custom dimensions and acceptance requirements are confirmed against the approved drawing and order specification. Confirm the standard edition, coating type, measurement area and test method on the order. The micrometre figures are approximate catalogue pairings, not a sum across two faces or an acceptance test.

Dimensions shown are the standard range. Non-standard lengths, hole patterns and coating weights are produced to order — send your drawing for a confirmation drawing.

Description

AASHTO M180 thrie-beam guardrail: where it is used

This page covers the thrie-beam rolled and galvanized specifically to AASHTO M180, the American specification for corrugated sheet steel beams for highway guardrail. It is the section ordered for US-funded projects and for export jobs that follow the AASHTO detail. The three-wave profile is used on bridges, ramps and high-speed alignment, and the galvanizing weight is what M180 actually governs.

Thrie-beam guardrail assembly drawing

What AASHTO M180 controls

Zinc coating mass: 300 / 550 / 610 / 900 / 1100 / 1220 g/m². Type I: 550 g/m²; Type II: 1100 g/m². Approximate coating thickness: 300 g/m² ≈ 40 µm; 550 g/m² ≈ 80 µm; 610 g/m² ≈ 85 µm; 1100 g/m² ≈ 160 µm; 1220 g/m² ≈ 170 µm. Confirm the standard edition, coating type, measurement area and test method on the order. The micrometre figures are approximate catalogue pairings, not a sum across two faces or an acceptance test.

Thrie-beam guardrail installed at the roadside

Rolling and fabricating the section

The coil is uncoiled, levelled and roll-formed into the three-wave profile, then cut to length and punched for the bolt holes before galvanizing. Galvanizing after forming means the cut edges are coated too, which is what M180 expects. We roll thrie-beam on the same line as W-beam, so a project using both sections gets consistent material and one set of documentation.

Thrie-beam section and component drawing

Standards, sizes and ordering

Our M180 thrie-beam is supplied with a mill certificate showing the steel grade and the coating weight, and lengths, hole patterns and end details are made to your drawing. Run lengths are cut to suit the site, and the beam can be shipped with the posts, blocks and bolts for the same run. Ask us for the coating test report with the quotation.

Where a thrie-beam wins over a W-beam section

Both sections are rolled from the same coil and galvanized to the same AASHTO M180 coating, so the difference between them is the profile, not the steel. The thrie-beam carries a third wave, which gives it a deeper section and a higher section modulus at the same nominal thickness. That is why it is ordered where a W-beam would otherwise need a heavier gauge, a shorter post spacing or an added blockout to reach the same containment.

  • A deeper three-wave profile than a W-beam at the same steel thickness
  • Higher stiffness and durability under repeated minor impacts
  • Absorbs more of the impact energy, over a longer length of rail
  • Redirects the vehicle back along the road with less lateral travel
  • Reads as a deliberate marker where a highway or a bridge deck begins
  • Discourages pedestrians from stepping onto the carriageway at the transition
  • Reduces the risk of a vehicle skidding off the edge on mountain roads and bridge decks

Where a project runs both sections — thrie-beam on the bridge approach, W-beam on the open alignment — ordering them from the same mill keeps the coating weight, the steel grade and the mill certificate consistent along the whole run.

Frequently asked questions

What is the difference between Type I and Type II thrie-beam to AASHTO M180?
Zinc coating mass: Type I: 550 g/m²; Type II: 1100 g/m². Nominal base thickness: Class A: 2.67 mm; Class B: 3.43 mm. Panel length: 4120 × 506 × 85 mm / 7920 × 506 × 85 mm. Custom dimensions and acceptance requirements are confirmed against the approved drawing and order specification.
What steel grade does an AASHTO M180 thrie-beam use?
Mechanical properties: Re ≥ 355 MPa; Rm ≥ 495 MPa; A50 ≥ 15%. For the specified high-strength steel grade; verify the grade and batch mill certificate. Steel grade: A572 / Q345B / HA350 / Q235B / A36 / S355JR / S275JR.
May the beam be galvanized before or after fabrication?
Both are done. Galvanizing after forming and punching coats the inside of the corrugation and the hole edges, while galvanizing before fabrication suits projects that follow an existing supply chain. The coating weight is the same either way: 550 g/m² minimum, or 1100 g/m² where a heavier coating is written into the specification.
What documentation comes with an AASHTO M180 order?
The mill test certificate for the coil, the coating weight report for the galvanizing batch and a dimensional check against the M180 table. That is the package a US-funded project or an AASHTO-detail tender normally asks to see before the shipment leaves the port.

Key features

  • Three-wave thrie-beam section for higher containment than a W-beam
  • Hot-dip galvanized, minimum 550 g/m² zinc coating to AASHTO M180
  • Produced in AASHTO M180, EN 1317 and national transit standards
  • Longer effective span between posts reduces post count and install time
  • Matched posts, spacers and terminals supplied in the same shipment

Where it is used

  • Bridges and viaducts
  • Tunnel portals
  • High-traffic corridors
  • High-speed motorways
  • Rail and metro corridors
  • Gantries and sign supports

Complete the system

A barrier is supplied as a set. These are the components that go with this item on a typical installation.

Not sure which specification fits?

Tell us the road class, design speed and the standard your client is working to. Our engineer will come back with the section, the coating weight and the post spacing that meet it — and the price for the quantity you need.

Ask an engineer
Related

Other items in this range

Thrie-Beam Guardrail
Thrie-Beam Guardrail

Thrie-Beam Guardrail

Model: Thrie-Beam / 506 / 508 / 510 mm

Thrie-beam panels have three corrugations and a deeper profile than W-beam panels. Confirm panel dimensions and matching components…

View details
Galvanized W-Beam Guardrail
W-Beam Guardrail

Galvanized W-Beam Guardrail

Model: W-Beam / 308–315 mm

Galvanized W-beam panels for roadside barrier systems. Send your approved drawing to confirm dimensions, steel grade, hole pattern,…

View details
Related

More on Thrie-Beam Guardrail

Need a quotation for your next highway project?

Send the drawing, the bill of quantities or just the standard you are building to. We return a take-off, a shop drawing and a factory price within one working day.

Chat on WhatsApp